SynthHub
Written from devices/akai/mpc2500.vendor.fw-1.21.json, updated 2026-10-27Edit on GitHubJSONCSVMIDNAMOSCQuery

Akai MPC2500 running MPC2500 Operator's Manual rev 1.0

The Akai MPC2500 MIDI implementation: 1 CC, 11 SysEx commands, each named, for Claude (MCP), SuperCollider or any OSC app.

  • sourcemaker's documentation
  • firmware1.21
Maker
Akai
Firmware
MPC2500 Operator's Manual rev 1.0 (June 2005) + Manual Addendum v1.21
Source
maker's documentation

Communities

Share and load its sounds

Plug the Akai MPC2500 into your computer, open shared presets in Chrome, Edge or Opera and press Connect my synth: SynthHub finds it, takes the sound it plays and names it. Sounds others shared for it load from their page the same way.

https://archive.org/details/manual_MPC2500_OM_AKAI_EN

Repository

MIDI controls

12 controls, from the source at MPC2500 Operator's Manual rev 1.0 (June 2005) + Manual Addendum v1.21

Channel mode

ControlCCRangeName to send
All notes off123trigger/mpc2500/all_notes_off

SysEx commands

CommandArgumentsName to send
Sequence selectsequence: u7/mpc2500/sequence/select
Transport clock/mpc2500/transport/clock
Transport start/mpc2500/transport/start
Transport continue/mpc2500/transport/continue
Transport stop/mpc2500/transport/stop
Song positionbeats: u14/mpc2500/song/position
Mmc deferred play/mpc2500/mmc/deferred_play
Mmc stop/mpc2500/mmc/stop
Mmc pause/mpc2500/mmc/pause
Mmc record strobe/mpc2500/mmc/record_strobe
Mmc locatehours: u7, minutes: u7, seconds: u7, frames: u7/mpc2500/mmc/locate

Performance MIDI

Notes, pitch bend and any CC are also available: /mpc2500/note/on <note> <velocity>, /mpc2500/cc/<number> <value>, /mpc2500/pitchbend <0-16383>, /mpc2500/program_change <n>.

JSON

Use it

Find the MIDI ports, then start the bridge with this driver:

osc-bridge detect        # prints the ready-to-run line for what is plugged in
osc-bridge run --device akai/mpc2500.vendor.fw-1.21 --out-port <N> --in-port <M>

Then send OSC to 127.0.0.1:7777, for example:

osc-bridge osc-send /mpc2500/all_notes_off 0

From Claude or any MCP client, the osc-bridge mcp server exposes this driver as mpc2500: ask “what can the Akai MPC2500 do?” and it reads this map with list_routes. See the MCP guide.

Programs and banks

A program change selects a sequence.

First switch on: Sequence change by program change ON.

Reading a stored sound back: it cannot be read over MIDI.

As the MPC1000: with the setting off, a program switches by its program change number.

Limitations

Source: Akai MPC2500 Operator's Manual rev 1.0 (MIDI implementation charts dated June 2005, 'Changing sequence by Program Change') and MPC2500 Manual Addendum v1.21 ('MIDI Machine Control', http://akaipro.com/documents/MPC2500/MPC2500_manual_addendumV1.21.pdf). The MIDI charts list the sampler (sound generator) section: notes 35-98 play the program's pads on its MIDI channel, Program Change 0-127 selects the program, channel pressure drives Note Repeat; the sequencer records and plays any channel message, which the performance routes cover. System Exclusive: recognized by the sequencer for recording only, no format given; not mapped. The manual gives no default pad-to-note table, so pads are not listed as triggers: notes 35-98 play whatever the program assigns to them. The MMC byte values are the MIDI standard's for the commands the addendum names; it does not print them. Untested on hardware.

Firmwares

The Akai MPC2500 runs 6 firmwares SynthHub maps, each with its own MIDI or another's it shares. All the devices with several: firmwares.

FirmwareFromLicenceMIDISounds
JJ's JJOS comparison chart and pageswww7a.biglobe.ne.jpsame as JJ's JJOS comparison chart and pages
JJ's JJOS comparison chart and pageswww7a.biglobe.ne.jpadds to MPC2500 Operator's Manual rev 1.0
JJ's JJOS comparison chart and pageswww7a.biglobe.ne.jpsame as JJ's JJOS comparison chart and pages
JJ's JJOS comparison chart and pageswww7a.biglobe.ne.jpadds to MPC2500 Operator's Manual rev 1.0
JJOS free 3.13www7a.biglobe.ne.jpsame as MPC2500 Operator's Manual rev 1.0
MPC2500 Operator's Manual rev 1.0archive.orgits own

Frequently asked questions

How many parameters of the Akai MPC2500 can be controlled over MIDI?

SynthHub's map of the Akai MPC2500 lists 1 MIDI CC parameters, each with its number, range and a readable name; the full chart is on this page.

Can an AI agent like Claude control the Akai MPC2500?

Yes: SynthHub's hosted MCP server knows the Akai MPC2500's MIDI map, and its browser relay lets the agent send it parameter changes or load a sound, each sound change confirmed by you.