devices/akai/mpc3000.vendor.fw-3.0.json, updated 2026-10-27Edit on GitHubJSONCSVMIDNAMOSCQueryAkai MPC3000 running MPC3000 Operator's Manual, Software version 3.0
The Akai MPC3000 MIDI implementation: 2 CC, 5 SysEx commands, each named, for Claude (MCP), SuperCollider or any OSC app.
- sourcemaker's documentation
- firmware3.0
- Maker
- Akai
- Firmware
- MPC3000 Operator's Manual, Software version 3.0
Communities
MIDI controls
7 controls, from the source at MPC3000 Operator's Manual, Software version 3.0
Channel mode
| Control | CC | Range | Name to send |
|---|---|---|---|
| All notes off | 123 | trigger | /mpc3000/all_notes_off |
Sound generator
| Control | CC | Range | Name to send |
|---|---|---|---|
| Master volume | 7 | 0–127 | /mpc3000/master/volume |
SysEx commands
| Command | Arguments | Name to send |
|---|---|---|
| Transport clock | /mpc3000/transport/clock |
|
| Transport start | /mpc3000/transport/start |
|
| Transport continue | /mpc3000/transport/continue |
|
| Transport stop | /mpc3000/transport/stop |
|
| Song position | beats: u14 | /mpc3000/song/position |
Performance MIDI
Notes, pitch bend and any CC are also available: /mpc3000/note/on <note> <velocity>, /mpc3000/cc/<number> <value>, /mpc3000/pitchbend <0-16383>, /mpc3000/program_change <n>.
Use it
Find the MIDI ports, then start the bridge with this driver:
osc-bridge detect # prints the ready-to-run line for what is plugged in
osc-bridge run --device akai/mpc3000.vendor.fw-3.0 --out-port <N> --in-port <M>
Then send OSC to 127.0.0.1:7777, for example:
From Claude or any MCP client, the osc-bridge mcp server exposes this driver as mpc3000: ask “what can the Akai MPC3000 do?” and it reads this map with list_routes. See the MCP guide.
Programs and banks
A program change selects a sound.
First switch on: Prog change RECEIVE (MIDI key, option 3: Sound Generator Input Filter).
| Bank | Bank select (CC 0 / CC 32) | Program change | Numbers | Shown as |
|---|---|---|---|---|
| Programs | – / – | 0–23 | 1–24 | 1-24 |
Recall one with /mpc3000/program/recall <bank> <number> (the bank by name, the number as shown).
Program changes 0-23 select programs 1-24, higher ones program 24; no bank select. Selecting a sequence sends each track's program number; on a DRUM track it changes the sound generator's program. Programs live on disk (PGM files); version 3.0 documents no program dump over MIDI.
Limitations
Source: Akai MPC3000 Operator's Manual, Software version 3.0 (MIDI implementation charts p.217-218 as printed, chapters 10 and 11). The sound generator plays MIDI notes 35-98: each is one of the program's 64 note slots, and each pad (A01-D16) sends the note the pad-to-note table gives it (MIDI key, option 1: per program or one master table). The manual gives no factory pad-to-note table, so pads are not listed as triggers: notes 35-98 play whatever the active program assigns to them. Incoming notes reach the sound generator on the active track's receive channel (1-16 or ALL) when a DRUM track is selected; with Local mode OFF the pads only send to MIDI OUT. Program Change 0-23 selects programs 1-24 when the Sound Generator Input Filter has Prog change set to RECEIVE (higher numbers select program 24); a sequence's tracks send their own program numbers when the sequence is selected. Channel pressure drives Note Repeat. The Note Variation slider follows one incoming controller whose number (0-127) is set on the unit, so none is fixed here; controller 64 is turned into note durations while recording unless 'Convert sustain pedal to duration' is OFF. System Exclusive is recorded into tracks (under 1000 bytes) and played back as recorded; the charts mark it sent and recognised by both sections but give no format: neither a Universal Identity Request nor a program or sound dump is documented for version 3.0. The sequencer recognises Song Select, but the manual does not say what it selects, so it is not mapped. MIDI clock, Song Position and Start/Continue/Stop are followed when Sync In mode is MIDI CLOCK (MIDI Time Code also, not mapped). The same document carries the Software version 3.1 update (MIDI Machine Control sent, MIDI Time Code sent while playing, MIDI Sample Dump both ways); this file is version 3.0 and maps none of it. 2 MIDI inputs, 4 MIDI outputs (A-D); no USB port in the specifications. Untested on hardware.
Frequently asked questions
How many parameters of the Akai MPC3000 can be controlled over MIDI?
SynthHub's map of the Akai MPC3000 lists 2 MIDI CC parameters, each with its number, range and a readable name; the full chart is on this page.
Can an AI agent like Claude control the Akai MPC3000?
Yes: SynthHub's hosted MCP server knows the Akai MPC3000's MIDI map, and its browser relay lets the agent send it parameter changes or load a sound, each sound change confirmed by you.